HP storageworks 4/16 SAN switch hardware

HP storageworks 4/16 SAN switch = Brocade SilkWorm 200e

Cpuinfo:
processor       : 0
cpu             : 440GP Rev. C
revision        : 4.129 (pvr 4012 0481)
bogomips        : 499.71
machine         : Brocade Silkworm440
plb bus clock   : 133MHz
pci bus clock   : 33MHz
uart clock      : 0KHz (internal)

lspci:

00:00.0 Host bridge: IBM: Unknown device 01ef (rev 01)
00:02.0 Network controller: Brocade Communications Systems Inc: Unknown device 000b

dmesg | less:

Linux version 2.6.14.2 (swrel@hq1-ub-ecbld-603) (gcc version 3.4.6) #1 Wed Dec 7 06:31:03 PST 2011
ppc440_setup_arch(): Not setting the 100MBFull for eth1 on this SWBD34
cpld_init: platform (34) not supported



Brocade Silkworm port (C) 2002 MontaVista Software, Inc. (source@mvista.com)
On node 0 totalpages: 32768
  DMA zone: 32768 pages, LIFO batch:15
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: quiet
PID hash table entries: 1024 (order: 10, 16384 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 123904k available (2400k kernel code, 664k data, 108k init, 0k highmem)
Calibrating delay loop... 499.71 BogoMIPS (lpj=2498560)
Mount-cache hash table entries: 512
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 2603k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
SGI XFS with no debug enabled
Initializing Cryptographic API
IBM gpio driver version 06.12.06
SWBD Platform Driver v1.0: [type 34, rev 1].
Config Silkworm
PPC 405 watchdog driver v0.51. (Timer driven)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at MMIO 0x0 (irq = 1) is a 16550A
ttyS1 at MMIO 0x0 (irq = 0) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 50000K size 1024 blocksize
loop: loaded (max 8 devices)
PPC 4xx OCP EMAC driver, version 3.54
mal0: initialized, 4 TX channels, 2 RX channels
zmii0: bridge in RMII mode
eth0: emac0, MAC 00:05:1e:07:51:ce
eth0: found Generic MII PHY (0x01)
emac1: can't find PHY!
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
read cpld_data 0x90
Silkworm CE-2 CPLD ATA interface configured [CPLD version 16]
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
cpld_ide_init_hwif_ports: dp=0, cp=0, hw=c0463f50
Probing IDE interface ide0...
hda: SILICONSYSTEMS INC 256MB-3620, ATA DISK drive
ide0 at 0xd301b1f0-0xd301b1f7,0xd301b3f6 on irq 28
hda: max request size: 128KiB
hda: 508928 sectors (260 MB) w/0KiB Cache, CHS=994/16/32
hda: cache flushes not supported
 hda: hda1 hda2
ATA polled-mode panic dumper on char-major-252.

Platfotm ID: SWBD34